Top 10 typical forklift crashes ， forklift procedure must focus on these matters ！.

Top 10 typical forklift crashes ， forklift procedure must focus on these matters ！.

Blog Article

Don't ignore the forklift at the workplace. If the procedure is bad, there will certainly be serious accidents in minutes, and there are numerous mishaps including forklifts.

Situation 1: The forklift cargo blocked the motorist's sight, and the person in front could not be found, resulting in a rolling accident.
Case 2: In order to maintain the equilibrium of the forklift when raising hefty products, the workers used their body weight as the counterweight, which almost caused casualties.
Instance 3: The size of the forklift freight surpasses the permitted width of the route and holds on the roadside rack, which almost causes an crash.
Instance 4: Forklift is speeding up and rolls over during a turn.
Case 5: The forklift driver did not see the pedestrian, and the pedestrian did not observe the forklift.
Situation 6: The forklift lifts the personnel unlawfully, the forklift chauffeur does not wear the safety belt, the forklift lifter drops and the chauffeur is crushed when the forklift surrender.
Situation 7: The forklift driver did not put on a seat belt and dropped from the automobile when it rolled over and was squashed.
Forklift operation should pay attention to these issues ：.

Start.
1. Prior to starting, observe the environments, and after verifying that there are no obstacles that prevent the security of driving, beep the horn first and then begin.
2. For vehicles with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) scale should be secure before starting.
3. When the forklift begins with a load, the motorist ought to initially confirm that the lots is stable and reliable.
4. The begin must be sluggish and steady.

Driving.
1. When driving, the height in between the bottom end of the fork and the ground ought to be maintained 300mm-400mm, and the pole ought to be slanted backward. .
2. Do not lift the fork expensive when driving. When entering and leaving the task website or while driving, be careful that there will be no barriers in the sky. When the tons is taking a trip, the fork must not be raised too expensive, which will certainly affect the stability of the forklift. .
3. After dumping, the fork should be lowered to the typical driving placement prior to driving. .
4. When turning, if there are pedestrians or cars close by, the driving signal needs to be issued first. High-speed sharp turns are forbidden. High-speed doglegs will certainly create the car to shed lateral stability and tip over. .
5. When the forklift is downhill, it is strictly prohibited to shut off the flame and slide, and it is restricted to brake all of a sudden while driving with lots unless there are unique situations.
6. When the forklift is running, it has to comply with the website traffic rules in the manufacturing facility and must maintain a certain safety and security range from the automobile ahead. .
7. When the forklift is running, the lots must be in the lowest placement that does not impede the driving, and the gantry should be properly tilted back. The load will not be elevated other than when stacking or packing. .
8. The elevation of the lots need to not obstruct the driver's sight. In special conditions, when the item influences the forward vision, drive at a low speed when reversing.
9. It is forbidden to turn on the ramp, nor to drive across the ramp. .
10. The safe driving speed of the forklift in the manufacturing facility location is 5 km/h, and it has to drive securely at a low speed when entering the production workshop location. .
11. When the forklift is lifted, lifted or driven, it is prohibited for workers to stand on the fork to hold items and play a balancing role. Electric Forklift Truck for Warehouse .
12. If problems are discovered, they will be repaired and reported in a prompt fashion, and they will never run with diseases or conceal them.

filling and dumping.
1. When fork-loading products, the range between both forks need to be readjusted as needed to make the lots of both forks well balanced and not skewed, and one side of the item must be against the shelf. .
2. It is restricted to deal with a single fork or make use of a fork top or draw. In special scenarios, safety and security indication need to be set up to remind surrounding pedestrians. .
3. In the process of filling and dumping products, the forklift must be stopped with the brake. .
4. The rate of the vehicle must be sluggish and consistent. Beware not to roll the wheels on the dunnage, so as not to extend the rolled things and harm individuals. .
5. When making use of a fork to fork the goods, the fork should be as deep as feasible under the tons, and it must be noted that the fork tip should not touch various other items or items. The load needs to be stabilized with very little back tilt of the gantry to make sure that the lots does not glide in reverse. The pole can be slanted forward a little when the tons is decreased to allow for very easy placement of the lots and extraction of the forks. .
6. It is restricted to fork items at high speed and hit tough objects with the fork head. .
7. When the forklift is working, it is prohibited for people to stand around the fork, so as to prevent the collapse of the goods and hurt people. .
8. Overwhelming is prohibited, and it is restricted to utilize forks to raise workers to engage in high-altitude procedures to stay clear of high-altitude dropping mishaps. .
9. It is not permitted to make use of the brake inertia to slip, place, round or roll things. .
10. It is not enabled to make use of forks to select, transform pallet unload.

Leaving .
1. It is prohibited to leave the forklift when the products on the fork impend. Before leaving the forklift, you should dump the goods or reduced the fork structure.
2. Pull the emergency brake deal with to dead or depress the emergency brake switch.
3. The engine is switched off and the power is cut off. (Except for special circumstances, such as the vehicle driver does not leave the lorry's view and does not surpass 1 minute).
4. Get rid of the trick. .

Forklift Operation Precautions.
1. Prior to and after the forklift operation, the appearance should be examined, and fuel, lubing oil and air conditioning water need to be added.
2. Inspect the safety and security performance of starting, running and stopping.
3. Check whether the lights and horn signals are total and reliable.
4. Throughout the procedure of the forklift, examine whether the pressure and temperature level are normal.
5. After the forklift is running, the exterior leak should additionally be examined and the seals should be changed in time.

Forklift Safety Operation Specifications.
1. You have to inspect prior to leaving the automobile;.
2. When you come across somebody in front of you during driving, you need to send out a signal at a distance of 5 m;.
3. The driving rate in the manufacturing facility does not exceed 5 km/h;.
4. When driving, the low point of the freight need to be 0.3 m ~ 0.4 m in the air;.
5. The transforming need to not be as well sharp to stop the propensity of "free turning";.
6. Running up and down the slope ought to be sluggish and consistent, and no switching on the slope is allowed.
7. Do not drive throughout the slope. When the slope is greater than 10%, the automobile must be driven backwards when declining;.
8. When the forklift workers bring the goods and move forward, if they run into big or hefty products and most likely to the driver's line of vision, they must take the turning around exercise
.
The "Eight Prohibitions" need to be complied with in the procedure.
1. Single fork operation is not allowed.
2. It is not allowed to lift the goods for cross country driving.
3. It is not allowed to grab the goods by handing over the pallet with the fork.
4. It is not allowed to Electric Forklift Truck for Warehouse directly shovel chemicals, flammables and other unsafe chemicals with forks.
5. It is not permitted to use inertia force to get the goods.
6. It is not allowed to utilize stopping pressure to exile round or easy-to-roll things.
7. It is not allowed to bring individuals to service the pallet or fork, and it is purely prohibited to stand under the fork after the fork is increased.
8. Do not drive laterally on inclines
.
Vehicle parking is not allowed under the following problems.
1. Curves, slim roads, train crossings;.
2. Sections with a longitudinal slope higher than 5%.
3. When there is an barrier on one side of the roadway, the contrary side of the section with the very same length as the challenge need to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：info2@onen.cn
Phone：+86 13827083844